In the following guide I explain how to remove and replace damaged LCD screen on HP G50/G60/G70 notebooks. I’m replacing it on a HP G50 but all disassembly steps should be almost the same or at least very similar for HP G60 and G70.
By the way, HP G50/G60/G70 models also known as Compaq Presario CQ50, Presario CQ60 and Presario CQ70.
In most notebooks you can replace the screen without separating the display panel from the base but not in HP G50/G60/G70.Â In these models we’ll have to remove display panel first.
By the way, in the next post I show how toÂ remove the motherboard.
You can find the HP spare part number in the service manual. I linked to service manuals at the end of this guide.
Turn off the laptop and remove the battery.
Remove one screw securing the Wi-Fi cover and remove the cover.
It is not necessary to remove the memory and hard drive covers. I marked them just for your convenience.
Remove three (yellow) screws securing the keyboard.
Remove four (red) screws securing the keyboard cover.
If you are using this guide for replacing the keyboard, you have to remove only three (yellow) screws.
In G50 and G60 the keyboard screws are located in the battery compartment.
In G70 notebooks there are only two screws securing the keyboard and they are located on the bottom (there is a small keyboard stamped close to each screw).
Carefully lift up the keyboard from the base.
Place the keyboard so you can access the cable connector underneath.
You have to unlock the connector and release the cable before removing the keyboard.
Move the white clip about 2-3 millimeters towards the display panel and release the cable. Now you can remove the keyboard.
WARNING! The white clip must stay attached to the connector base. If you accidentally break the connector, you’ll have to replace the motherboard. If you work slowly, everything should be fine.
On the picture below the connector is shown in the unlocked state.
Disconnect the switch board cable from the motherboard.
Remove the keyboard cover.
Move the cover towards the display to separate from the top cover.
Turn the laptop upside down and disconnect two antenna cables from the wireless card.
Each antenna cable has a golden head. Grab the head with your fingers and lift it up.
Disconnect the video cable connector from the motherboard.
Disconnect the webcam cable from the motherboard.
Pull two Wi-Fi antenna cables through the opening.
Remove four screws securing the display panel hinges.
Lift up and separate the display panel from the base.
In the following steps we will disassemble the display panel and remove the LCD screen.
There are two screw seals located in the lower left and right corners.
Remove these seals with a sharp object and remove screws found under the seals.
Start separating the bezel from the display cover.
Continue separating the bezel.
The bezel has been removed.
The inverter board is mounted on the bottom side of the display cover. The inverter is locked between plastic brackets.
You can remove and replace the inverter board without removing the screen. Simply pull the inverter board from the cover and disconnect connectors on both ends.
Remove two screws securing the right display hinge.
Remove the right hinge.
Remove two screws securing the left display hinge.
Remove the left hinge.
Remove the inverter board from the cover and disconnect one connector from the right side. By the way, this is the backlight connector.
Remove two screws securing the mounting brackets on the top.
Now you can separate the LCD screen from the display cover and access the video cable.
My HP G50 notebook didn’t have the webcam installed and the webcam cable was taped to the display cover.
If you have a HP G60/G70 notebook, most likely it came with the webcam. You’ll have to disconnect the cable from the webcam before disconnecting the video cable.
Remove sticky tape securing the video cable connector and unplug the video cable.
Now you can remove the LCD screen from the cover.
If you are replacing it, you’ll have to transfer the left and right mounting brackets to the new screen.
Remove three screws securing the bracket and remove the bracket. Do the same with the other side.
The LCD screen model number is located on the sticker. In my laptop I had this model installed: B154EW08 v.1