Home
In the following guide I’ll be taking apart a Gateway NX570X laptop. I think my disassembly instructions will work for other Gateway laptops in the NX570 line too. Please let me know if you have a different Gateway laptop and this guide works for you, you can mention your model in the comments below.
The laptop I’m fixing stopped charging the battery even though the AC adapter works properly and outputs correct voltage. I tested the adapter with a voltmeter. Actually, it’s charging the battery but only intermittently, when the AC adapter pushed in firmly. In order to charge the battery I have to adjust the AC adapter plug inside the power socket on the back of the laptop. Apparently, there is a problem with the power socket (aka power jack) and it has to be replaced or resoldered. OK, let’s take this lappy apart. I’ll be removing the system board so I can access and repair the power jack.
Are you looking for spare parts for your Gateway NX570 laptop? You’ll find them here.
STEP 1.
Turn off the laptop, unplug the AC adapter and remove the battery.
Remove seven screws (yellow circles) securing the memory cover.
Remove one screw (yellow circle) securing the keyboard. There are two more keyboard screws under the memory cover. You can see them in the step 5.
Remove one screw (orange circle) securing the Wi-Fi card cover.
Remove two screws (red circle) securing the hard drive. In order to disconnect the hard drive from the motherboard, you’ll have to slide the hard drive assembly to the left. Remove the hard drive assembly from the laptop.
STEP 2.
Disconnect two antenna cables from the wireless card, simply unsnap them from the card using your fingers. Remove one screw securing the wireless card and remove the card.
Remove both memory modules.
Loosen four screws securing the heat sink assembly (red circles).
STEP 3.
Carefully lift up the heat sink assembly from the laptop. The cooling fan is attached to the motherboard. Unplug this cable from the motherboard.
STEP 4.
Remove one screw securing the CD/DVD drive. Push the drive to the left and remove it from the laptop.
STEP 5.
Remove all screws from the bottom of the laptop. Two screws marked with green circles are securing the keyboard.
If you are replacing the keyboard, you simply remove one green screw in the step 1 and two green screws in the step 5 and then proceed to steps 7,8,9,10.
STEP 6.
Remove two screws from the hinge cover.
STEP 7.
Start removing the hinge cover with a small flathead screwdriver and continue removing it with your fingers.
STEP 8.
Remove the hinge cover.
STEP 9.
Lift up the keyboard as it shown on the picture below and place it upside down on the palm rest.
STEP 10.
Unlock connector on the system board. Release the cable and remove the keyboard.
STEP 11.
Release the wireless card antenna cables.
Unplug LCD cable from the system board.
Remove two screws from each display hinge.
STEP 12.
Carefully lift up and remove the LCD assembly.
STEP 13.
Remove four screws securing the top cover.
Unplug the touch pad cable from the system board.
STEP 14.
Lift up and remove the top cover assembly.
STEP 15.
Remove five screws securing the motherboard.
Unplug the speaker cable (left) and the Bluetooth card cable (right) from the system board.
STEP 16.
Start removing the system board from the left side.
You’ll have to disconnect one more cable shown on the picture below.
Finally, the system board has been removed.
Now you can access and repair the power jack. You can use these power jack replacement instructions.
When I was removing the power jack from the system board, it came out with the internal sleeve attached to the “+” connector. This sleeve connects traces on both sides of the system board and normally, when you unsolder the power jack, it stays inside the hole.
Now I’ll have to make a modification so traces on both sides of the system board are connected. I’ll have to connect traces with a cable.
August 20th, 2012 at 5:51 pm
@ Silent,
Probably the server was busy. Refresh the page (F5).
August 20th, 2012 at 2:48 pm
All the pictures are Broken.
August 15th, 2012 at 3:35 pm
I used this guide to disassemble my Gateway MT6728 and it was the same for the most part. I spilled iced tea inside and wanted to clean any residue to see if I could get it running again as it was dead after the spill. Still no luck, though. The symptoms are: Blue power button lights up, front LEDs light up, cooling fan runs, CD drive appears to spin or some other component makes a noise. Screen remains black/blank and can be shut down again by pressing the power button.
I let it dry initially, took everything apart, cleaned inside, reseated the ram, HD. Also tried to boot without HD, swapped the RAM in opposite slots, tried booting with/without battery still to no avail.
Any ideas?
July 23rd, 2012 at 10:59 am
@ Lisette,
I guess you are talking about the DC jack which is shown on the last picture of my guide. Correct?
In order to fix the DC jack it’s necessary to disassemble the laptop, remove the motherboard, and replace the DC jack (requires soldering). Can you do it yourself? If not, you’ll have to take it to the repair shop.
July 21st, 2012 at 12:52 pm
Hello, so I tripped on the charger and the inside of the computer thing broke. Would I need Togo to a shop to have it repair? Or can I do it myself? It’s that thingy in the inside of the computer when you charge it that broke.
June 20th, 2012 at 4:01 am
Hi im having some trouble taking out the green screw thats appears in the first photo, its like stuck to the plastic, ive tried everything to take it out, but it wont seem to loosen up. Got any solution for me?
February 1st, 2012 at 4:22 pm
@ sarah,
Did you break the keyboard connector locking tab?
Take a look at these posts:
http://www.laptoprepair101.com/laptop/2009/11/17/fix-broken-keyboard-connector-on-laptop-motherboard/
and
http://www.laptoprepair101.com/laptop/2011/12/25/how-to-repair-broken-touchpad-connector-on-laptop-motherboard/
Hopefully it will give you the idea how to fix the connector.
January 30th, 2012 at 8:03 am
hi
i have a problem great instruction , installed new dc re- putting together but hit a snag
step 10 says in reverse connect system board but it broke in half and I can not see how to put the platis thing back. will it work in two halfs
do I need tobuy an ew one if so what is it called and can you give instructions how to instal this fidle part as the plastic thing came out.
January 17th, 2012 at 10:59 am
Hello, how are you? I have on my desk a Gateway 6020GZ, which has the integrated burning PQ38, I ask because I see that is very similar, I thank you if you can tell me what kind of integrity (integrated above numbers), apologizes for the English, the translated with google translator, I’m from Montevideo, Uruguay, thanks and sorry for the inconvenience
December 16th, 2011 at 11:34 pm
Thanks for these awesome guides! Just installed new power plug for Gateway MX6453. Only one screw different on the model. It has one less than yours, but everything is close enough that it works. Laptop running again. Thanks!